.code16
.section .boot,"a"
- mov $0x13, %ax
- int $0x10
-
- mov $1, %al
- mov $0x3c8, %dx
- outb %al, %dx
- mov $0x3c9, %dx
- mov $63, %al
- outb %al, %dx
- xor %al, %al
- outb %al, %dx
- outb %al, %dx
-
- mov $200, %ebx
- mov $0x00000101, %eax
- pushl $0xa000
- popl %es
- xor %di, %di
-fill:
- mov %ebx, %ecx
- and $1, %ecx
- jnz 0f
- rol $16, %eax
-0: mov $80, %ecx
- rep stosl
- dec %ebx
- jnz fill
+ .set scratchbuf, 0x7b00
+boot:
cli
+ cld
+ # move stack to just below the code
+ xor %ax, %ax
+ mov %ax, %ss
+ mov $0x7b00, %sp
+ # use the code segment for data access
+ mov %cs, %ax
+ mov %ax, %ds
+ mov %ax, %es
+
+ mov %dl, drive_number
+
+ call setup_serial
+
+ # load the second stage boot loader and jump to it
+ mov $_boot2_size, %eax
+ mov %eax, %ebx
+ shr $9, %eax
+ and $0x1ff, %ebx
+ jz 0f
+ inc %ax
+0: pushw %ax
+ pushw $1
+ # set es to the start of the destination buffer to allow reading in
+ # full 64k chunks
+ mov $boot2_addr, %bx
+ shr $4, %bx
+ mov %bx, %es
+ xor %bx, %bx
+ call read_sectors
+ jmp boot2_addr
+
+ .set SECT_PER_TRACK, 18
+
+ .set ARG_NSECT, 6
+ .set ARG_SIDX, 4
+
+# read_sectors(first, num)
+read_sectors:
+ push %bp
+ mov %sp, %bp
+
+ mov ARG_SIDX(%bp), %ax
+ xor %cx, %cx
+
+ jmp 1f
+0: push %ax
+ call read_sector
+ pop %ax
+ inc %ax
+ inc %cx
+1: cmp ARG_NSECT(%bp), %cx
+ jnz 0b
+
+ pop %bp
+ ret
+
+ .set VAR_ATTEMPTS, -2
+str_rdsec_msg: .asciz "rdsec: "
+str_cyl_msg: .asciz " C "
+str_head_msg: .asciz " H "
+str_sec_msg: .asciz " S "
+
+# read_sector(sidx)
+read_sector:
+ push %bp
+ mov %sp, %bp
+ sub $2, %sp
+ push %cx
+ push %dx
+
+ movw $3, VAR_ATTEMPTS(%bp)
+
+.Lread_try:
+ # calculate the track (sidx / sectors_per_track)
+ mov 4(%bp), %ax
+ mov $str_rdsec_msg, %si
+ call print_str_num16
+
+ xor %dx, %dx
+ mov $SECT_PER_TRACK, %cx
+ div %cx
+ mov %ax, %cx
+ # save the remainder in ax
+ mov %dx, %ax
+ # head in dh
+ mov %cl, %dh
+ and $1, %dh
+ # cylinder (track/2) in ch [0-7] and cl[6,7]<-[8,9]
+ rol $7, %cx
+ ror $2, %cl
+ and $0xc0, %cl
+ # sector num cl[0-5] is sidx % sectors_per_track (saved in ax)
+ inc %al
+ or %al, %cl
+
+ mov $str_cyl_msg, %si
+ mov %cx, %ax
+ rol $2, %al
+ and $3, %al
+ ror $8, %ax
+ call print_str_num16
+
+ mov $str_head_msg, %si
+ xor %ax, %ax
+ mov %dh, %al
+ call print_str_num16
+
+ mov $str_sec_msg, %si
+ mov %cl, %al
+ and $0x3f, %ax
+ call print_str_num16
+
+ # ah = 2 (read), al = 1 sectors
+ mov $0x0201, %ax
+ movb drive_number, %dl
+ int $0x13
+ jnc .Lread_ok
+
+ # abort after 3 attempts
+ decw VAR_ATTEMPTS(%bp)
+ jz .Lread_fail
+
+ # error detected, reset controller and retry
+ xor %ah, %ah
+ int $0x13
+ jmp .Lread_try
+
+.Lread_fail:
+ mov 4(%bp), %ax
+ jmp abort_read
+
+.Lread_ok:
+ # DBG print first dword
+ mov $str_read_error + 4, %si
+ mov %es:(%bx), %eax
+ call print_str_num
+
+ # increment es:bx accordingly (advance es if bx overflows)
+ add $512, %bx
+ jno 0f
+ mov %es, %ax
+ add $4096, %ax
+ mov %ax, %es
+
+0: pop %dx
+ pop %cx
+ add $2, %sp
+ pop %bp
+ ret
+
+str_read_error: .asciz "err read sect: "
+
+abort_read:
+ mov $str_read_error, %si
+ call print_str_num16
hlt
+cursor_x: .byte 0
+
+ # prints a string (ds:si) followed by a number (eax)
+print_str_num:
+ push %eax
+ call print_str
+ pop %eax
+ call print_num
+ mov $13, %al
+ call ser_putchar
+ mov $10, %al
+ call ser_putchar
+ ret
+
+print_str_num16:
+ push %eax
+ and $0xffff, %eax
+ call print_str_num
+ pop %eax
+ ret
+
+ # expects string pointer in ds:si
+print_str:
+ push %es
+ pusha
+
+ pushw $0xb800
+ pop %es
+ xor %di, %di
+ movb $0, cursor_x
+
+ push %si
+
+0: mov (%si), %al
+ mov %al, %es:(%di)
+ movb $7, %es:1(%di)
+ inc %si
+ add $2, %di
+ incb cursor_x
+ cmp $0, %al
+ jnz 0b
+
+ pop %si
+ call ser_putstr
+
+ popa
+ pop %es
+ ret
+
+ # expects number in eax
+print_num:
+ # save registers
+ push %es
+ pusha
+
+ xor %cx, %cx
+ movw $scratchbuf, %si
+ mov $10, %ebx
+
+0: xor %edx, %edx
+ div %ebx
+ add $48, %dl
+ mov %dl, (%si)
+ inc %si
+ inc %cx
+ cmp $0, %eax
+ jnz 0b
+
+ # print the backwards string
+ pushw $0xb800
+ pop %es
+ movb cursor_x, %al
+ xor %ah, %ah
+ shl $1, %ax
+ mov %ax, %di
+
+0: dec %si
+ mov (%si), %al
+ movb %al, %es:(%di)
+ call ser_putchar
+ inc %di
+ mov $7, %al
+ movb %al, %es:(%di)
+ inc %di
+ dec %cx
+ jnz 0b
+
+ # restore regs
+ popa
+ pop %es
+ ret
+
+ .set UART_DATA, 0x3f8
+ .set UART_DIVLO, 0x3f8
+ .set UART_DIVHI, 0x3f9
+ .set UART_FIFO, 0x3fa
+ .set UART_LCTL, 0x3fb
+ .set UART_MCTL, 0x3fc
+ .set UART_LSTAT, 0x3fd
+ .set DIV_9600, 115200 / 9600
+ .set LCTL_8N1, 0x03
+ .set LCTL_DLAB, 0x80
+ .set FIFO_ENABLE, 0x01
+ .set FIFO_SEND_CLEAR, 0x04
+ .set FIFO_RECV_CLEAR, 0x02
+ .set MCTL_DTR, 0x01
+ .set MCTL_RTS, 0x02
+ .set MCTL_OUT2, 0x08
+ .set LST_TREG_EMPTY, 0x20
+
+setup_serial:
+ # set clock divisor
+ mov $LCTL_DLAB, %al
+ mov $UART_LCTL, %dx
+ out %al, %dx
+ mov $DIV_9600, %ax
+ mov $UART_DIVLO, %dx
+ out %al, %dx
+ shr $8, %ax
+ mov $UART_DIVHI, %dx
+ out %al, %dx
+ # set format 8n1
+ mov $LCTL_8N1, %al
+ mov $UART_LCTL, %dx
+ out %al, %dx
+ # clear and enable fifo
+ mov $FIFO_ENABLE, %al
+ or $FIFO_SEND_CLEAR, %al
+ or $FIFO_RECV_CLEAR, %al
+ mov $UART_FIFO, %dx
+ out %al, %dx
+ # assert RTS and DTR
+ mov $MCTL_DTR, %al
+ or $MCTL_RTS, %al
+ or $MCTL_OUT2, %al
+ mov $UART_MCTL, %dx
+ out %al, %dx
+ ret
+
+ # expects a character in al
+ser_putchar:
+ push %dx
+
+ mov %al, %ah
+ # wait until the transmit register is empty
+ mov $UART_LSTAT, %dx
+0: in %dx, %al
+ and $LST_TREG_EMPTY, %al
+ jz 0b
+ mov $UART_DATA, %dx
+ mov %ah, %al
+ out %al, %dx
+
+ pop %dx
+ ret
+
+ # expects a string in ds:si
+ser_putstr:
+ mov (%si), %al
+ cmp $0, %al
+ jz 0f
+ call ser_putchar
+ inc %si
+ jmp ser_putstr
+0: ret
+
+
+drive_number: .byte 0
.org 510
.byte 0x55
.byte 0xaa
+
+boot2_addr: